| GRINDERS
and ACCESSORIES |
| Part Number |
Product
Description |
Price |
| GEO600 |
Makita
die grinder 25,000 RPM, 110V, 2.5 AMPS with a 1/4” collet chuck.
For all porting, except flapper sticking. (Use an air grinder for
that.) |
$135.00 |
| 608LB |
front
spindle & front armature bearings (ea.) |
$5.00 |
| 627LB |
Rear
armature bearing |
$5.00 |
| 213373-4 |
O-ring
for front spindle bearing case |
$0.80 |
| 263002-9 |
Rubber bearing retainer pins
1/8”, 4 needed |
$2.25 |
| 181675-5 |
Grinder case, 2 pieces |
$30.00 |
| 3415533 |
Chromed steel locking cap for
front case |
$7.00 |
| 643057-4 |
Armature
brush set CB-57-75, set of 2 |
$5.00 |
| 643552-4 |
Brush holder |
$2.00 |
| 763626-6 |
1/8” collet |
$14.95 |
| 763625-8 |
1/4” collet |
$14.95 |
| 763606-2 |
Collet nut |
$5.00 |
| 321194-1 |
Front spindle |
$34.00 |
| 9510573 |
Front spindle and armature drive
spring pins |
$1.00
|
| 4109864 |
Front spindle and armature drive
coupler |
$3.25 |
| SC600-B |
Complete front spindle with
bearings, o-ring, drive pin |
$49.00 |
| 651600-5 |
Switch |
$10.00 |
| 664013-1 |
Molded grinder cord with plug |
$9.00 |
| 682500-8 |
Cord guard |
$2.00 |
| 687001-1 |
Cord bracket |
$1.50 |
| 911133-5 |
Cord bracket screws, each |
$0.60 |
| 611401-3 |
Armature complete with fan
bearings & drive pin |
$52.75 |
| 911148-2 |
Case screw with washer, sold
individually |
$0.60 |
| 621386-5 |
Armature field |
$23.65 |
| 961004-6 |
Snap ring for front spindle
bearing |
$0.40 |
| 781003-0 |
10mm wrench |
$4.00 |
| 781008-0 |
17mm wrench |
$4.00 |
| AG3751 |
Florida
Pneumatic 20,000RPM air grinder with extra large bearings. Has 1/4”
collet with 1/8” reducer. Air exits out front to blow off work area.
We use this grinder for polishing only. Porting needs more power
& stability. |
$69.00
|
| AG45 |
Chicago Pneumatic
22,000RPM Air Grinder - with 45° head angle and adjustable air pressure
and speed. The greatest for porting manifolds, cranks, grinding chassis
welds, deburring, etc. Many uses in hard-to-reach areas. Comes in both
1/4" and 6mm collett. Free speeds up to 22,000 RPM. Needs 90psi air
pressure. Air consumption 10cfm. |
$139.00 |
| 6681 |
Rheostat speed reducer controls
grinder speed when connected in-line with your plug-in receptacle strip so
you can adjust between 12,000 & 25,000 RPM |
$12.00
|
| RCB-100 |
A protective
rubber collet boot to eliminate nicks and grooves on cylinder head intake
and exhaust surfaces including the deck |
$1.00 |
| AR32 |
airline pressure reducer valve
with stainless steel ball for years of service.
One end is 1/4” male, other 1/4” female pipe end.
A must for porting & polishing with air |
$12.00 |
| TD500 |
Machined tool steel drivers for
1/2X.500 O.D. SS thin-wall sleeve installation.
Make sure there is no more than .001 press fit between the sleeve
& the reamed hole. Use
epoxy or green Loctite Sleeve Retaining Compound to retain & seal the
sleeve especially if the hole is larger than the sleeve. If the sleeve is
larger than the reamed hole either
polish out the hole with a cartridge roll or polish the outside of the
sleeve in a drill press or lathe. |
$15.00 |
| TD562 |
same as the TD-500 for 9/16 x
.5625 sleeves |
$15.00 |
| TD625 |
same as the TD-500 for 5/8 x.625
sleeves |
$15.00 |
| TD750 |
same
as the TD-500 for 3/4 x.750 sleeves Other O.D. sleeves are
special order |
$15.00
|
| PORTING
SERVICE TOOLS |
| Part Number |
Product
Description |
Price |
| SV400 |
Swivel
Vice
mounts anywhere, swivels 360°, sweeps 180°. Ideal for porting small 1
& 2 cylinder engines. Use
our 12mm & 14mmX 6” mandrels for heads.
Recommended for use with V.W. 100 mounting brackets for V.W. heads. |
$49.00 |
| ASW3 |
Adjustable
Spanner Wrench for use with the SV-400 to tighten vice down & prevent
movement. A must to keep vice tightened |
$33.00 |
| MM12 |
Aluminum
Mandrel 6” long with 12mm threads. Use with SV-400 vise |
$15.00 |
| MM13 |
Stainless
Steel Mandrel 6” long with 12mm threads. Use with SV-400 vise |
$20.00 |
| MM14 |
Stainless
Steel Mandrel 6” long with 14mm threads |
$15.00 |
| SV425 |
Pro Series Heavy Duty Vice with Manual Tightening
Handle; swivels 360° & sweeps 180°; weight capacity is 20 lbs. Made
of cast iron & steel. Ideal
for Harley Davidson &
similar small heads. Not recommended for V.W. heads.
|
$99.00 |
| MM12P |
Mandrel same
as MM-12 for the SV-425 Pro Series vice |
$15.00 |
| MM14P |
Mandrel
same as MM-14 for the SV-425 Pro Series vice |
$15.00
|
| VW100 |
T-Shaped
Holding Fixture with 8” Extension fits SV-400 vice; bolts to
1200-1800 V.W. valve cover studs with spacers.
Kit comes with brackets, extension, spacers, nuts & washers |
$35.00 |
| SG-LED |
Illuminated
Porting Safety Goggles - Have built in LED lights on either side so
you can see everything while porting, polishing, doing valve work,
close-up examinations of parts, and many other uses. Lights are adjustable
up and down, several styles available. Batteries included. Please specify
style; Wrap Around (Style 1), Regular w/lenses (Style 2), and Frame (Style
3) w/o lenses. |
$24.95 |
